My '72 1600 SSS

Show everyone your mean datto projects/rides
broke
Datsun Addict
Posts: 998
Joined: Mon Apr 04, 2011 11:25 pm
aka: John
Location: Christchurch

Re: My '72 1600 SSS

Post by broke »

Did some welding today. It's not good enough for Weld Porn or anything, but it's not bad enough for "Welding Fails" either.
IMG_2197.JPG
You can see the space I'm aiming to fit it into here. Hoses will be cramped, but I'll make it work somehow. Also if I ever do this again I'm going to use those weld on UN o-ring bosses, as it's damn hard to get the torch into the right spot when you have two male fittings side by side.
IMG_2201.JPG
Then welded this mounting strap on top. Still need to get an alloy fuel pump mount and weld it to this, then buy fuel pumps and start plumbing them in. Nabbed lots of R14 teflon hose before I left Hydraulink, so that should help keep costs down :D
You do not have the required permissions to view the files attached to this post.
2 doors
Datsun God
Posts: 2499
Joined: Sat Jul 19, 2008 6:26 pm
Location: Christchurch

Re: My '72 1600 SSS

Post by 2 doors »

making progresss ,looks good
User avatar
85_Z31
Datsun Master
Posts: 1494
Joined: Sun Jul 18, 2010 10:53 pm
Location: Rangiora North Canterbury

Re: My '72 1600 SSS

Post by 85_Z31 »

looks good nice work.
The Answer to your Question is NEEDS MORE VG30
broke
Datsun Addict
Posts: 998
Joined: Mon Apr 04, 2011 11:25 pm
aka: John
Location: Christchurch

Re: My '72 1600 SSS

Post by broke »

Finished the surge tank, still waiting for my fuel pumps to arrive.

In the meantime I started ripping into this gearbox tonight - even with the factory repair manual I managed to lose 3 spring loaded ball bearings taking 6th gear off. Took a wee while to find them all too...
IMG_2253.JPG
Got this far. I need to invent or modify some special tools to go any further than this, might have a crack at that after work tomorrow.
IMG_2255.JPG
IMG_2258.JPG
You do not have the required permissions to view the files attached to this post.
User avatar
torqued
Datsun God
Posts: 2124
Joined: Sat Jul 19, 2008 11:49 am
aka: Adam
Location: Christchurch

Re: My '72 1600 SSS

Post by torqued »

Lol, Is that still in your spare room?
"It's ok, we know what to do...we talked about this a lot on the internet."
User avatar
brocky41
Financial Member
Posts: 1764
Joined: Sat Jul 19, 2008 11:05 am
aka: Brocky
Location: Christchurch
Contact:

Re: My '72 1600 SSS

Post by brocky41 »

Lol - i dont have curtains like that in my shed.

I hope you covered the floor in plastic and cardboard before you started with that gearbox.

I like your surge tank and where its located - keep up the good work.
broke
Datsun Addict
Posts: 998
Joined: Mon Apr 04, 2011 11:25 pm
aka: John
Location: Christchurch

Re: My '72 1600 SSS

Post by broke »

torqued wrote:Lol, Is that still in your spare room?
Not any more haha. :D

Followed the factory manual which says to use a puller and slide hammer to remove 6th gear. I tried for ages and couldn't get it to budge, even tried winding in the centre bolt of the balancer puller to the point where the threads in 6th gear hub started pulling out!
IMG_2265.JPG
IMG_2266.JPG

Eventually I gave up and set it up like this on the bench - I think the "shock" force of the slide hammer is really necessary for pulling the gears and not having it solidly braced was absorbing that force.
IMG_2267.JPG
Many, many max effort slams later and it came off, so abruptly that I almost fell over backwards. Went scrabbling on the ground looking for springs and ball bearings again...

After that it wasn't too hard to get the centre casing off, then I ran out of time
IMG_2269.JPG
You do not have the required permissions to view the files attached to this post.
broke
Datsun Addict
Posts: 998
Joined: Mon Apr 04, 2011 11:25 pm
aka: John
Location: Christchurch

Re: My '72 1600 SSS

Post by broke »

This box was advertised as working but being hard to shift in the lower gears. I bought it thinking that was probably a good thing, as it's usually 4th that gives up and then everything explodes and it's useless Fortunately the gears look fine, there were an awful lot of metal fragments here though - the box has a big magnet sitting in the bottom of the casing as well as the one on the drain plug, neat touch I thought.

Upon closer inspection it looks to me that these shards are from 4th gear contacting the gear next to it and being eroded slowly, the synchro rings don't look too flash either. I'll know more once I disassemble the cluster, it looks salvageable to my untrained eye though.
You do not have the required permissions to view the files attached to this post.
broke
Datsun Addict
Posts: 998
Joined: Mon Apr 04, 2011 11:25 pm
aka: John
Location: Christchurch

Re: My '72 1600 SSS

Post by broke »

I think I found the issue.

That haggard looking metal collar thing is a bush for the shift fork where it slides on the shifter rod. The other damaged one was way worse - The teflon/bronze lining had completely disintegrated, the steel backing was all chewed up and the whole thing had dropped right out so the fork was flopping around like a cock in a sock.

That explains why I kept finding all those bits of plastic type fragments everywhere.
IMG_2285.JPG
IMG_2284.JPG
IMG_2280.JPG
It's a non standard sized 15x17 bush. Went to Saeco and got some 16x18 DU bushes hoping the extra interference on the OD would decrease the ID but it was still too sloppy. I'll ask about some proper sized ones tomorrow. Hopefully they can get something.
You do not have the required permissions to view the files attached to this post.
2 doors
Datsun God
Posts: 2499
Joined: Sat Jul 19, 2008 6:26 pm
Location: Christchurch

Re: My '72 1600 SSS

Post by 2 doors »

good work, gearbox,s can be like voodoo black magic to work on.
Post Reply